|
|
|
Who's Online
There currently are 6029 guests and
2 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
NAD S400
NOTE: Return to step #3 and perform the same alignment procedure but substitute L2 for L1. Continue to align L10, L7, L2, and L1, until there is no improvement in IF-level maximum level between the two antenna ports, and that the isolation between the two ports is greater that 40 dB. Alignment of IF Section: 6)
Connect an RF signal generator to ANTENNA port #1 and set to: Amplitude = 45 dBu Pilot tone = off Modulation = off Frequency = 98.000 MHz. Press the ANTENNA-button and select ANTENNA port #1. Press the IF-button to select IF WIDE. With the same oscilloscope setup as in procedure #3, check that the IF-signal had increased approximately 3 dB compared to IF NARROW. Remove the oscilloscope probe from the common point between CF3 and CF4.
Adjust L13 (or VR1) until the centre-tune LED turns on. Fine adjust VR1 so that it lights from approximately 97,965 MHz. to 98,035 MHz equally. Alignment of Audio Section: 8) Set the S400 as the following: Press the IF-button to select IF WIDE. Press the ANTENNA-button and select ANTENNA 1. Press the MONO/MUTE-button to MUTE OFF MONO. Press the BLEND-button to BLEND OFF. Press the BANDWIDTH-button to BANDWIDTH WIDE. Tune the S400 to 98.00 MHz. Connect an audio AC voltmeter with decibel display to both the right and left audio output jacks. Set the AC-voltmeter to negative 30 dB range. Leave the audio AC-voltmeter attached to the S400 audio output jacks until told to remove it. Then connect an RF signal generator to ANTENNA port #1 and set to: Amplitude = 45 dBu Pilot tone = on (19 kHz @ 10%) Modulation = off Frequency = 98,00 MHz Adjust L3 for a minimum 19 kHz output at the right audio jack. Adjust L4 for a minimum 19 kHz output at the left audio jack
9)
10) 11)
y
r
7)
Connect an RF signal generator to ANTENNA port #1 and set to: Amplitude = 70 dBu Pilot tone = off Modulation = off Frequency = 98.000 MHz.
a
ni
m
i
el
r
P
5)
4)
With the same oscilloscope setup as in procedure #3, press the ANTENNA button and select ANTENNA port #1. Check that the IF-signal is reduced by a minimum of 40 dB. Connect the signal generator to ANTENNA port #1. With the same oscilloscope setup as in procedure #3, adjust L2 until the IF-signal is at maximum setting. Press the ANTENNA button and select ANTENNA port #2. Check that the IF-signal is reduced by a minimum of 40 dB.
 $4.99 S400 NAD
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|
